It is very common for one of these tractors to have parts with casting date codes that don't exactly match. Tractor assembly would probably have been several days or longer after the engine passed QC and was stamped with a serial number. In the case of an engine block, final assembly and testing had to take place before the hand-stamped serial number was added.
#1974 ford tractor serial number guide code#
What all that means is the casting date code on any part must be at least 30 days prior to the part being machined. Wnen each engine passed QC Inspection/Testing, the hand stamped serial number was applied, and the engine was placed in another holding area. Machined blocks were then taken to the engine assembly area where they were fully assembled and then placed in another holding area.Īssembled engines then went to the QC Test Area. The date code F262 indicates June 26,1959.Īgain, the fresh "green" castings are too brittle for machine work, so they were placed in a holding area for at least 30 days.Įngine blocks were then pulled from the holding area to be fully machined, cleaned, and then set in another holding area. The next two numbers indicate day of the month, a final number indicates year. Date codes varied but the most common code found on the 9N, 2N, 8N tractors is a letter indicating the month A=Jan, B=Feb, C=MAR. The tag and screws are visible on the casting. Casting date codes will have raised or recessed numbers and letters on a tag that was attached to the mold with screws. Fresh "green" castings are brittle and will break tools or the casting if machine work is attempted too soon. There are no identifying marks to indicate the exact date a tractor was assembled.Ĭast parts were have date codes that the factory used to make sure parts were properly cured before being machined. These hand-stamped numbers were the last identifying mark added before final assembly of a tractor.
#1974 ford tractor serial number guide serial numbers#
The hand-stamped engine serial numbers for 9N,2N,8N tractors only indicate approximately when a tractor was built. The N-Tractors used an odd font with lowercase "b" substuted for "6", flipped upside down for "9" and the capital "I" substituted for "1".
Hand-stamped means the numbers may be difficult to read if the hammer didn't get a really good whack on each character. The exact location changed and is described below for each model. Model and serial numbers for all Ford tractors were hand-stamped into the cast iron engine or transmission housing. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.FORD N-TRACTOR SERIAL NUMBERS AND CASTING DATE CODES Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. John Deere and its logos are the registered trademarks of the John Deere Corporation. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. websites are the property of their respective trademark holders.
products and within the Yesterday's Tractor Co. TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Latest Ad: 16 x 38 double bevel rims, sealed and paintedĬopyright © 1997-2022 Yesterday's Tractor Co.Īll Rights Reserved.
for use as a sightseeing ride at the Niagara Falls State Park, Niagara Falls, New York, powered by a 1959 Ford 611 Tractor. of Buffalo, New York designed and built six Viewmobiles for the Niagara Frontier Sightseeing Inc. In 1959 the Niagara Frontier Transit Inc. Today's Featured Article - The Niagra View Mobile - Powered by a 1959 Ford Tractor - by Mark Massey. Our low prices and years of research make us your best choice when you need parts. We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Leaking power steering fluid out of the stġ974 5000 remote hydraulic valve and accessory plate.ġ974 Ford 3000 Hydrolic fluid lifting slow or not at allġ974 Ford 4000 Diesel Tractor Wiring Diagram no crank againġ973-75(?) Warner Swasey rough terrain forklift Ford 3000ġ974 5000 diesel. Of 1416.36 ġ973 Ford Tractor, Model 2000, 3 cylinder, gasġ973 ford 2000 gas wiring diagram needed.